| VT365 no start | |
|
|
Author | Message |
---|
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: VT365 no start Tue Jun 14, 2016 12:51 pm | |
| ok I have a VT365 that has a hard start issue when it gets hot I have a couple actually but I'm working on 2 atm the first we changed the high pressure pump, injectors, and oil rail tubes the second we changed the High pressure pump and oil rail tubes and neither bus will restart and we get good ICP 1200 - 1400 cold we have fuel and at least 40 psi oil pressure is it possible we got bad High pressure pumps or am I missing something?? Chad Frost Lakeside #12 | |
|
| |
b1
Posts : 56 Join date : 2016-04-07
| Subject: Re: VT365 no start Tue Jun 14, 2016 1:00 pm | |
| | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Tue Jun 14, 2016 1:06 pm | |
| yes there is fuel pressure we even have 30 psi of air pressure going into the tank to push the fuel | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Tue Jun 14, 2016 1:34 pm | |
| I think I'm gunna try a test and reinstall the old high pressure oil pump ans see what happens
Chad Frost | |
|
| |
b1
Posts : 56 Join date : 2016-04-07
| Subject: Re: VT365 no start Tue Jun 14, 2016 2:36 pm | |
| Are you sure you don't have ECM or IDM Relay problems? Replacing the HP oil pump when you have good pressure doesn't make sense. Check fuel pressure with a guage. Do you have any active codes? | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Wed Jun 15, 2016 5:26 am | |
| | |
|
| |
b1
Posts : 56 Join date : 2016-04-07
| Subject: Re: VT365 no start Wed Jun 15, 2016 7:40 am | |
| I want you to do an injector test and then do the ECM and IDM test on the no start sheet. Post the results. | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Wed Jun 15, 2016 2:33 pm | |
| how long does the injector test normally run for. I ask because the injectors have been buzzing away for about 30 min.+ now | |
|
| |
b1
Posts : 56 Join date : 2016-04-07
| Subject: Re: VT365 no start Wed Jun 15, 2016 2:57 pm | |
| Don't know I put Fuel adapter in you box | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Thu Jun 16, 2016 8:09 am | |
| the relay voltage for the ECM and IDM while cranking is 9.6v as for the injector test the injectors buzzed for 1 hour then we just stopped the test | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Thu Jun 16, 2016 10:38 am | |
| | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Thu Jun 16, 2016 2:11 pm | |
| Swapping the IDM from its sister bus didn't make a diff. | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Wed Jun 22, 2016 12:47 pm | |
| compression results were
1- 200 2- 200 3- 200 4- 200 5- 320 6- 180 7- 170 8- 210
| |
|
| |
b1
Posts : 56 Join date : 2016-04-07
| Subject: Re: VT365 no start Wed Jun 22, 2016 2:28 pm | |
| Pull the engine for rebuild. | |
|
| |
b1
Posts : 56 Join date : 2016-04-07
| Subject: Re: VT365 no start Wed Jun 22, 2016 2:30 pm | |
| I want you to do a compression check on the other no start before we do anything else to it. | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Thu Jun 23, 2016 5:34 am | |
| they other one I figured out it was a bad oil temp sensor repaired that and that one finally started | |
|
| |
b1
Posts : 56 Join date : 2016-04-07
| Subject: Re: VT365 no start Thu Jun 23, 2016 7:19 am | |
| Good was there a code for that sensor? | |
|
| |
lakeside
Posts : 28 Join date : 2016-04-20
| Subject: Re: VT365 no start Thu Jun 23, 2016 7:29 am | |
| not at first but when we pulled it back in the engine light was on and told use were to go | |
|
| |
Sponsored content
| Subject: Re: VT365 no start | |
| |
|
| |
| VT365 no start | |
|